|
|
Billet Aluminum Trim
All Split 'n' Pinned products are an exclusive trademark of Watson's StreetWorks.
Exclusively
 by StreetWorks
Steering Column Trim
Give your steering column the finished look with our machined aluminum trim with heavy duty rubber seal. Made with StreetWorks unique Split 'n' Pinned design for easy installation - no column removal required. The ring measures 3.420" I.D. and 4.800" O.D. and includes stainless steel mounting screws. The rubber seal has an opening to fit GM and other columns measuring 1-3/4" to approximately 2-1/8" diameter. Some trimming may be required for larger diameters.
Now with an additional grommet to fit 1-1/2" diameter columns. |
 |
|
#B03N |
$39.00 |
| #B03S (Rubber Seal, Only) |
$20.00 |
| #B03R
(Aluminum Ring w/Screws, No Seal) |
$25.00 |
Oval Brake & Clutch Trim
Use on cars with elongated pedal shafts. Also great for use
on the firewall with accelerator cable and kick down and for some TPI
applications. Choose from a solid machined part or our Split 'n' Pinned
trim. Both are 2-1/4" diameter with a 5/8" x 1-1/8" hole and stainless steel
screws and rubber gasket. |
 |
|
#B02 (Solid) |
$15.95 |
|
#B02S (Split 'n' Pinned) |
$19.95 |
Oval Hole/Oval Body Brake & Clutch Trim
Great new Oval shaped body. For elongated or
rectangular pedal shafts Also trim the firewall for accelerator cable
and kick down or for some TPI applications.
1-5/8" X 2-1/4" wide. 5/8" x 1-1/8" hole. Stainless steel screws, Rubber gasket, Split 'n' Pinned trim. |
 |
|
#B02OVS (Oval Split 'n' Pinned) |
$24.00 |
For a solid Oval trim, see our #B14OV-PLT
Round Brake & Clutch Trim
Small, round hole trim allows you to finish the brake and clutch pedal shafts and around the dimmer switch. Also great for around wires, hoses, harnesses or anything you want to trim. Choose from a solid machined part or our Split 'n' Pinned trim. Both are 2-1/4" diameter with a 15/16" diameter hole and stainless steel screws and rubber gasket (not in photo).
|
 |
|
#B01 (Solid) |
$15.95 |
|
#B01S (Split 'n' Pinned) |
$19.95 |
Pass Through Trim
For use with wires, bundles, harnesses, cables, etc. Has an insulated rubber grommet with 5/8" I.D. Overall size is 2-1/4" O.D. with stainless steel screws. |
 |
Or use our Split 'n' Pinned version that was designed specifically for use with the Howell Engineering TPI and TBI harnesses. Has smaller #4 screws that are closer to the outer edge to cover a hole up to 1-5/8" wide.
|
#B01ST (Split 'n' Pinned) |
$24.00 |
Brake Pedal Hole Trim Plate
From our friends at Sachse Rod Shop. Each piece is 2" X 4" with a 1/2" wide slot. Overlapping feature allows the slot to be 1-1/4" to 2" long. 18 gauge steel. 1 Predrilled holes and stainless screws. Helps make installation very simple.
|
  |
| #SA-6510 (2 plate pieces and 4 screws) |
$12.00 |
Trik-Trim Billet Upholstery Plate
Add the distinct look of billet to complement and finish your upholstery project. This attractive billet oval will set off your ride as the one to emulate. Oval is 1-1/2" X 1-5/64" with milled, raised edge. Put on the doors, seats...almost anywhere that you would like an accent. Details are what it's all about and these are great additions. Fastens with blind stud and hardware included. Milled finish is easy for you to polish.
|
New !
|
Billet Wire Port
Here is a great way to dress up the area of the firewall where
the wiring harness goes through. The Wire Port main body
is 2" dia. with a 1-1/2" inside dia. and is secured to the firewall
around the wire bundle hole with four (4) truss head screws.
A 1" x 13/16" deep cut-out in the Wire Port body allows the
wire bundle to exit close to the firewall (a rubber grommet is
included for smaller wire bundles). The body is then capped
off with an attractive machined cover which has three (3)
ball-milled grooves. The design allows for the wire bundle
to be installed before the final attachment of the Wire Port is
done. Attractive, functional and at a very reasonable price.
|
New !
|
Billet Wire Pass-through
A really attractive way to dress up the area where the wires come through the firewall. Unit measures 1-1/2" wide X 2" tall X 1" deep with a wire exit size of 1" wide X 3/4" deep. Blind fastens from behind for that smooth look.
Hardware and template included.
|
  |
Billet Drink Holder
What
do you do??? You're at the Burger-Doodle drive-thru window, get your
double-burger, large fries and drink - the burger and fries kinda' stay
in the bag, but the drink has got to go between your legs. So now you're
steering with your left hand, your right hand is bouncing between the
stick shift, french fries and burger, left leg clutch, right leg
brake...and that drink is r-e-a-l-l-y cold. ● Get
our beautiful, Billet Drink Holder! ● Magnetic
base holds tight on the glove box door, yet removes easily to store in
the glove box. 3" I.D. x 2-1/8" deep holds most drink cups. ● Inner
plastic cup to catch condensation. ● Dual-black
O-rings for added looks.
|
|
Great gift idea! Machined aluminum drink holder with O-rings and magnetic base!
|
|
|
