Door Solenoids Plus
|
StreetWorks Door Solenoids
You want more power. You want fast action. StreetWorks Solenoids have
it. They work the way you want, with 40 pounds of pull so they work with
original latches. Solenoids, cables, pulleys, connectors, wire hardware
and instructions. Solenoid and bracket measure approximately 2-3/4"
wide x 2-1/16" high (thick) x 4-1/4" long.
|
 |
|
#L22N (2 Door Set Up, Shown) |
$150.00
|
|
#L22NS (1 Door Set Up) |
$80.00
|
|
#L22NX (2 Solenoids w/Brackets Only) |
$130.00
|
|
#L22NXS (1 Solenoid w/Bracket Only) |
$70.00
|
"The whole job from start to finish went perfect because of the quality of the Solenoid kit. You can buy less expensive stuff but you sure couldn't duplicate the quality/power/ durability of your product. I guess that's when less expensive becomes Cheap!!" Joe DeBilio, California
Booster Springs
For those really tough original latches that need an extra "boost" to open, these springs will provide a preload on the latch mechanism so that less force is needed to release the latch. 4-1/2" long zinc plated high-carbon steel springs have 4.40 pounds/inch of force. The cable connector allows you to adjust the pull to your needs.
|
|
|
#L22-B (2 sets, as shown) |
$10.00 |
|
#L22-BS (1 set) |
$5.00 |
Stainless Steel Braided Door Wire Looms
The added looks of stainless braid, the door
jams are 1/2" O.D. x 3/8" I.D. x 7+" effective length.
One fixed and one sliding threaded
aluminum boss. Plastic lined.
Mount into 3/4" Diameter holes with jam
nuts included.
|
 |
| #TP-SSDWL-1/2 (2 door
pair as shown) |
$40.00 |
Stainless Steel Braided Door Wire Looms for Suicide Doors
These wire looms can open to more than 200 degrees and not bind! Swivel ball bushings assure smooth operation. 1 1/2" O.D. X 3/8" I.D. X 7+" length, plastic lined S/S Braid. New Quick Collar ends. Ball swivel flange end mounts vertically and is just 2" high.
|
 |
| #TP-SUICIDE (2-door pair) |
$80.00 |
We've tried our darnedest to force these to bind but they won't!
They'll work great on non-suicide doors, too.
Nylon and Billet Door Wire LoomsThe look of Billet & Black, the door looms are 1/2" O.D. x 3/8" I.D. x 7+" effective length. 1 One fixed and one sliding aluminum boss. Plastic lined. 1 Mount into 3/4" and 5/8" Diameter holes with set screw secured "quick" collars. |
 |
| #TP-NYLON-1/2 (2 door pair as shown) |
$28.00 |
Medium Plastic Wire Looms
These plastic wire looms for door jams are 5/8" O.D. x
3/8" ID. x 7+" long. Fixed grommet at one end for the door jam.
Sliding grommet for the other end goes into the door. More than twice
the wire capacity as 1/4" I.D. tubing. Requires 3/4" and 7/8" Diameter
holes. Hot rod black. |
 |
|
#P-MWL (2 door
/pair)..................................................Only |
$15.00 |
Giant Plastic Wire Looms
These giant wire looms are 1" O.D. x 3/4" 1.D. x 7+"
long with a fixed grommet at one end and a sliding
grommet for the other end. Will handle LOTS of wires.
Mount into 1-3/8" Diameter holes. Hot rod black.
|
 |
|
#P-GWL (pair)..... Only ..... |
$15.00 |
Magnum Shooters
Door jam wire contacts eliminate looms and wire flexing. With screws and connectors. Per door. |
 |
|
#DD-MGS2 (2 contact, shown at right)
|
$16.50 |
|
#DD-MGS3 (3 contact)
|
$21.95 |
|
#DD-MGS4 (4 contact, shown at left)
|
$27.50 |
|
#DD-MGS4P (4 contact + pin switch)
|
$32.95 |
|
#DD-MGS5 (5 contact)
|
$32.95 |
Gear Motor Actuator
For bear-claws and some original latches made after
about 1960, these actuators will provide the power needed to trip the
latch. Tested at 13 pounds of pull, with a 7/8" travel, these will also
work for door locks when used with a polarity reversing module (such as
our #L07-W). The actuator comes with the mounting and connecting
hardware shown.
(Actuator measures 5-1/4" long x 2-1/4" High x
1-1/8" Deep) |
 |
Spring Loaded Door Popper
5 inch overall length as shown. 1-5/8" plunger, can be shortened.
Maximum push at full plunger depression is 15 pound force. With mounting
plate and screws. Push plate to protect paint with 3M tape for
attaching.
|
 |
| #SP-DP (each as Shown) |
$20.00 |
|
