LED 3rd Brake Lights
Billet Pedestal LED 3rd Brake Light
with Turn Signals
|
National Street Rod Association
Best New Safety
Product of the year 2001
Runner up
|
|
We've taken Pedestal 3rd Brake Lights to a new level! This gorgeous piece is 16-5/8" wide, 3/4" high (body), 1-1/8" deep and only 2" tall including the swivel base. 60 super bright red LED's are split into 3 groups of 15-30-15 so that you have a 30 LED center 3rd brake light and (2)-15 LED turn signal/ brake lights. You could also add our LED Conversion Kits to get taillight and turn/brake or wire then all as one big and bright 3rd brake light. You've gotta' love this!
15% Brighter Clear Lens!
How do you make the best Billet Pedestal 3rd Brake light even better??? Make it even brighter! And we did. Our wonderful 3rd Brake Light is now 15% brighter and still with built-in turn signals. 60 super bright red LED’s behind a clear lens with diffuser. Ya’ gotta love it! |
|
Small Billet Pedestal
3rd Brake Light
with Turn Signals
8-7/8" wide, 3/4" high (body), 1-1/8" deep and only 2" tall including the swivel base. 30 super bright red LED's.
3 groups of 10 LED's provide a dedicated center 3rd Brake Light and Brake/Turn Signals on each end. |
 |
#L61SM (classic red lens) |
|
15% Brighter Clear Lens!
Our Small Billet Pedestal 3rd Brake Light is also 15% brighter and still with built-in turn signals. 30 super bright red LED’s behind a clear lens with diffuser. Ya’ gotta love it! |
|
Billet Pedestal Extension
Extends the mounting base on any of the Billet Pedestal lights, above by 2-7/8" allowing them to be adjustable in height and position. Fit split window rods or vehicles with glass curvature where the light can not be mounted directly at the glass edge.
|
 |
Flush Mount 3rd Brake Light with Turn Signals
 |
| 3rd Brake Light with Turn
Signals Our #L58B above, but two steps better. 3 groups of
15-30-15 provide a 30 LED center 3rd brake light and (2)-15 LED turn
signal/brake lights. Or add our LED Conversion Kits to get taillight
and turn/brake or wire them all as one big and bright 3rd brake light.
How c-o-o-l! |
Flush Mount Sequencing 60 LED 3rd Brake Light |
 |
| Get their attention with our Sequencing 60 LED 3rd Brake Light. It's split 10-10-20-10-10 and sequences inside-out once when the brakes are first applied then stays on solid. Flush mounting, build-in lens is 1/2" wide X 15-1/4" long. |
If you want to make this light into an extra taillight, too. Just add this convertor.
Billet Frames for StreetWorks L58 Series LED Lights
If you aren't into flush mounting taillight or 3rd brake light lenses into the body, these stunning machined billet aluminum frames work with our L58 kits to allow you to surface mount the lens on the outside of the sheet metal while the LED's and housing attach to the inside. The large L58 Frame is 16-3/4" long X just under 1" wide. It will protrude .400" off the surface. They accept our lenses perfectly (as shown). All other parts (lens, LED's, housing, etc) are in the flush mount kits, just add these frames for flat surface mount installation. 3rd Brake Light kits need one frame, Taillight Kits need two frames.
|
Small Flush Mount Hot Slot 3rd Brake Light w/Turn Signals
Like our full size Hole Slot lights except with 30 Super Bright Red LED's. A single intensity light but split 10-10-10 so that your turn signals will also be displayed. (Can also be wired as one solid 30 LED unit.) Red lens is1/2" wide by 7-1/2" long. |
|
Billet Frames for StreetWorks L58SM Series LED Lights
If you aren't into flush mounting taillight or 3rd brake light lenses into the body, these stunning machined billet aluminum frames work with our L58SM kits to allow you to surface mount the lens on the outside of the sheet metal while the LED's and housing attach to the inside. The small L58SM Frame is 9" long X just under 1" wide. It will protrude .400" off the surface. They accept our lenses perfectly (as shown). All other parts (lens, LED's, housing, etc) are in the flush mount kits, just add these frames for flat surface mount installation. 3rd Brake Light kits need one frame, Taillight Kits need two frames.
|
"Skinny" Flush Mount
Hot Slot 3rd Brake Light w/Turn Signals
"Like our full size Hole Slot lights except with 30 Super Bright Red LED's. A single intensity light is split 10-10-10 so that your turn signals will also be displayed. (Can also be wired as one solid 30 LED unit.) The lenses are 7-1/2" long by 1/4" wide (about .230" actually) for that disappearing-3rd-brake-light effect."
|
Deep Mount Small Hot Slots !
Flush Mounts
For Curved Surfaces
Now for the first time, install flush mounted lights into curved surfaces! Our deep acrylic lenses and steel support boxes allow you to contour the flush mount surface as much as 3 inches. Fit under curved rear windows. 30 Super Bright Red LED strips per light. Lenses are only 1/2" wide by 7-1/2" long! (Surface dimension will vary due to curvature.) These are a weld-in or glass-in kit requiring very good body working skills.
|
 |
Small Deep 3rd Brake Light w/Turn Signals
"Our Deep 3rd Brake Light with 30 Super Bright Red LED's. A single intensity light is split 10-10-10 so that your turn signals will also be displayed. (Can also be wired as one solid 30 LED unit.)."
|
|
Brake Light Pulsator
Get their attention fast when your brake lights pulsate at 300 pulses
per minute (5 per second!). Simple two wire connection - cut the feed
wire to the light(s) and install the STOP-ALERTTM with the terminals provided. Works for third brake lights or main brake
lights or both. Solid state, uses no additional power. Rated at 60 watts
continuous (5 amps incandescent), great for two #1157 bulbs or Ultra
Brights plus a 3rd brake light (for Halogen taillights, one per light is
needed).
Only 1-3/4" x 7/8" x 1-1/8. |
 |
3rd Brake Light Flasher
Makes your 3rd brake light flash 5 seconds when applied then come on solid. Get their attention without blinding them. It starts the flash over again when you reapply the brakes. Three wire connection, with terminals. Works with LED's or bulbs. Solid state, uses no power. Rated at 60 watts (5 amps incandescent), great for two #1157 bulbs or Ultra Brights plus a 3rd brake light (not for Halogen taillights). Small 1-3/4" x 7/8" x 1-1/8". |
|
60 LED 3rd Brake Light
You-build-it-in LED. Ultra-bright OEM style red LED's in red lens housings. 4 Mounting tabs on the back Water resistant.
|
 |
| #L51-60 (15-5/8" L x 1/2" Th x 1 to 1-5/32" Dp) |
$50.00 |
"6-to-12" 3rd Brake Light Converter
Don't feel stuck with dull tail and brake lights just because you still have the original 6 volt electrical system. This converter allows you to install a 12vdc LED negative ground 3rd Brake Light in a vehicle that has a 6 volt negative or positive ground electrical system. 1/2 amp maximum load.
Easy installation. Works with any-and-all of StreetWorks LED 3rd brake lights.
|
 |
Do-It-Yourself LED StripsRed LED's for Do-It-Yourself projects. All strips are 5/16" wide X 1/2" high (overall) X the length listed below.
As Do-it-yourself items, these are sold without warranty.
|
|
| #L73-5 (5-LED strip, 1-1/4" long) |
$10.00 |
| #L73-10 (10-LED strip, 2-9/16" long) |
$15.00 |
| #L73-15 (15-LED strip, 3-7/8" long) |
$20.00 |
| #L73-20 (20-LED strip, 5-3/16" long) |
$25.00 |
| #L73-30 (30-LED strip, 7-3/4" long) |
$30.00 |
| #L73-60 (60-LED strip, 15-3/8" long) |
$50.00 |
Other sizes are available (in 5-LED increments)- please call!
Amber LED's for Do-It-Yourself projects. All strips are 3/8" wide X 1/2" high (overall) X the length listed below. As Do-it-yourself items, these are sold without warranty.
| #L73A-4 (Amb 4-LED strip, 1-3/8" lg) |
$10.00 |
| #L73A-8 (Amb 8-LED strip, 2-3/4" lg) |
$15.00 |
| #L73A-12 (Amb 12-LED strip, 4-3/16" lg) |
$20.00 |
| #L73A-16 (Amb 16-LED strip, 5-9/16" lg) |
$25.00 |
| #L73A-20 (Amb 20-LED strip, 6-15/16" lg) |
$30.00 |
| #L73A-24 (Amb 24-LED strip, 8-5/16" lg) |
$35.00 |
| #L73A-28 (Amb 28-LED strip, 9-11/16" lg) |
$40.00 |
| #L73A-32 (Amb 32-LED strip, 11-1/8" lg) |
$45.00 |
NOTE: These are single intensity lights. Should you want them to work like a dual intensity light, for example as an auxiliary running light (less bright) and turn signal (full bright), you will also need to purchase our conversion kit.
| #L-JE03 (for L73A-4/8 or L73-5/10/15/20, one per light) |
$5.00 |
| #L-JE02 (for L73A-12/16/20/24/28/32 or L73-30/60, one per light) |
$5.00 |
LED Conversion Kit
Make any of the 3rd brake light LED's on this page act like a double
filament light - diminished intensity for taillight and full intensity for
brakes/turn signals. One needed for each LED brake light.
Lens Material
●Red lenses
material for your project. ●Red
translucent acrylic with or without diffuser 3" x 12" pieces only.
● 1/4" thick lens.
|
|
|
#P-RLM (Red translucent acrylic, each) |
$15.00
|
|
#P-RLD (Red translucent acrylic with diffuser, each) |
$25.00
|
|
#P-CLD (clear acrylic with diffuser, each) |
$25.00
|
Rod-Bits:
A good, large 3rd brake light is one of the most simple things that you can add to your vehicle, and it is the Number One safety item, too. You must make sure that people behind you can see that you are stopping. Put a bright LED 3rd Brake Light "in-their-face" - mount it as close to eye level as possible and aimed straight backwards. The bigger the better - don't skimp on safety, it's your rear end that they will run into!
And how can Watson's StreetWorks help keep you safe? Award Winning LED 3rd Brake Lights - that pretty much says it all. But then we give you variety as well - Billet Pedestal LED 3rd Brake Lights, Flush mounted LED 3rd Brake Lights, large, small, skinny, framed, unframed. Yeah, we know, so many choices, but would you want it any other way?
|
