LED Tail Lights & Flush Mount LED Taillights
 |
Confused about tail light functions and LED taillights? Helpful Tip:
Talkin' about Taillights. |
IMPORTANT NOTICE ABOUT LED TAILLIGHTS
LED tail lights from Watson’s StreetWorks are designed and intended for vehicles manufactured prior to DOT requirements (1/1/1968), for custom show vehicles or other off-road applications. If the light(s) are installed in later vehicles and are in addition to the original stock taillights or are being used as side markets, etc., you are in compliance. However, they do not meet DOT requirements unless specifically stated in our description.
Most all of our lights have been wired to be able to be used on vehicles with either integral brake/turn signals or separate brake and turn signal wiring. Certain OEM vehicles had “special” flashers or systems to detect burnt out bulbs - for these vehicles, LED lights typically DO NOT WORK unless the original flasher/system is bypassed or eliminated. For any application, if you are not sure of how our lights will work in your vehicle, call and ask. We are here to help.
Bullet Beehive LED Taillights
w/ Billet Base
'50's styling with 21st century technology. Each light has 13 Super Bright Red LED's in a Beehive light that has a neat star pattern. Machined Billet Base provides a high-tech finishing touch. Easily mounted to a flat surface using the hardware provided - only three holes needed to install. Dual intensity convertor included. Overall dimensions are 2-3/4" diameter x 2-7/8" tall. Use as a pair or in groups of four or six for that classic taillight look. These lights meet DOT/SAE requirement J592e and are so marked. |
 |
| #L84R-Bullet Beehive LED Taillights w/ Billet Base (Pair) |
$89.00 |
Amber, too! Bullet Beehive LED
Park Lights w/ Billet Base The perfect match to our Beehive Taillights. Each light has 13 Super Bright Amber LED's in a Beehive light that has a neat star pattern. Works great as the rear turn signal for vehicles that have separate turn signals.
| #L84A - Bullet Beehive LED Park Lights w/ Billet Base (Pair) |
$89.00 |
Oval Chrome Billet Hot Rod Mirrors
with Front and Rear Facing LED's
These classy Oval Chrome Billet Aluminum Mirrors have built-in LED's. Ten forward facing amber LED's work as both park lights and turn signals. Five rear facing red LED's are turn signal indicators. Each mirror is 3-1/4" X 5-1/4". Provided with three different sets of mounting hardware to better match your installation needs. This product is covered by a one year/12,000 mile Warranty by the manufacturer, Muth Mirror Systems.
|
One-Piece Flush Mount Hot Slot LED Taillight Kit
We've put 120 super bright red LED's into a single, one-piece taillight kit - single slot red lens measures 30-3/4" long X 1/2" wide to provide an uninterrupted, smooth look. Diffuser attached. Will work in surfaces with gradual curvature up to about 2-1/2". The LED's are dual intensity for taillights and brake/turn signals and are premounted into an aluminum housing. We also provide an aluminum "spacer box" to fill the gap created by body curvature and to seal out dirt and water - simply cut to the contour of the body. Weld-in or glass-in studs for mounting are included. Note that this is a build-in kit requiring extensive paint and body working skills.
|
Need the lens for your own project? Red with diffuser, 30-3/4" long X 1/2" wide with rounded ends.
| #L68-LENS (Lens Only) |
$75.00 |
Rectangular Flush Mount
LED Taillights
A BIG and LONG cut above the rest! The 60 LED strips fit inside an aluminum housing and mount behind build-in, flush mounted acrylic lenses which have clear prismatic diffusors.
The 1/4" thick acrylic lenses allow you to fit these lights into curved fenders,
roll pans and pickup bed corners and form them for that seamless look (the
acrylic lenses are not intended to be bent). Taillight Hot Slots have dual
intensity for taillights and turn-brake lights. The 3rd Brake Light
Hot
Slot is single, full intensity. They need approximately 1" of clearance
space behind the fender surface. Weld-in or glass-in studs for mounting
are included, as well as quality instructions.
Taillight Hot Slots - The acrylic lenses are only 1/2" wide by 15-1/4" long! Red LEDs shine through red lenses with
diffusers.
Each light is split 40/20 to work with either integral turn signal/brakes or separate turn signal systems. |
HOT SLOTS ! |
Add LED's to your ride |
Example of lights installed |
Call today - 860.859.0513 |
 'Hot Slot' Flush Mount
LED Taillights with Separate Amber Turn Signals
If you have turn signals that are separate from the brake lights, this kit is exactly what the doctor ordered. Each light has 40 super bright red LED's that handle the taillight and brake light functions, plus an additional 12 super bright amber LED's that are dedicated for turn signals. They are all mounted inside a ready-to-mount aluminum housing. The lenses are 1/4" thick build-in, flush mount units that measure 15-1/4" long X 1/2" wide clear acrylic with prismatic diffusers. Please note that these are build-in lights that require paint and body skills. Not all vehicles with separate turn signals are adaptable to LED lights. Call us to discuss your application.
|
 |
| #L58RACL (Taillight pair) |
$195.00 |
Flush Mount LED Taillight with Red Taillight/Brake and Sequential Amber Turn Signals
This great LED taillight has 40 bright red LED’s in each light that are dual intensity for both taillights and brake lights plus 12 super bright amber LED’s that will sequence 4-4-4 for the turn signals. Clear build-in lenses with diffusers are 15-1/4” long X 1/2” wide, sequencing modules, LED flasher and mounting hardware. |
|
| #L58RACL-SEQ (Taillight pair) |
$325.00 |
Double-D LED Taillights
Double-D taillights with twice the diodes. Two strips of 60 Super Bright Red LED's per light, inside an aluminum housing. 1/4" thick build-in, flush mounted red acrylic lenses with prismatic diffusers. Each strip is split 40-20 and the strips are wired separately so that you may wire the strips together or not. Work with integral turn/brake systems or vehicles with separate turn signals. The lenses are 1/2" wide x 15-1/4" long. Mounting hardware and dual intensity convertors included. |
|
| #L58-DDR - Double-D LED Taillights (Pair) |
$260.00 |
| Also available with clear lenses with diffusers. #L58-DDCL (Pair) |
$260.00 |
Double-D LED Taillights
with Bright White LED Backup Lights
Double-D taillights with twice the diodes - two strips of 50 super bright LED’s per light plus 3-(3) LED bright white clusters for backup lights all inside an aluminum housing. Build-in, flush mount clear acrylic lenses are 1/4” thick, 1/2” wide and 15-1/4” long plus diffuser. Each red strip is split 30-20 and are wired separately so that you can wire the strips together or not. Works with integral turn/brake systems or on vehicles with separate turn signals. Hardware and dual intensity convertors included. |
|
| #L58-DD-BU (taillight pair) |
$375.00 |
Sequential LED Taillights !
A real attention getter! Our #L58 taillights above, but three steps better. Each light is split into three groups of 20 LED's that sequence inside-out with the turn signals. Brake lights quickly sequences once then all stay on. All the necessary convertors and sequencing modules are included along with great instructions. Includes electronic flasher for flasher operations. |
 |
| #L58-SEQ (taillight pair) |
$325.00 |
Sequencing LED Taillights
for cars with Separate Turn Signals
These taillights are split 30-10-10-10 so that the inner 30 LEDs are the brake light and taillight and the outer 30 sequence 10-10-10 with the turn signals so they work on cars that originally had separate turn signals.
Flush mounting, build-in lenses are 1/2" wide X 15-1/4" long. With hardware, electronic flasher and instructions.
(Separation at right shown for the left taillight unit.) |
 |
| #L72-SEQ (taillight pair) |
$325.00 |
Additional resistors may be required for your application.
Billet Frames for StreetWorks L58 Series LED Lights
If you aren't into flush mounting taillight or 3rd brake light lenses into the body, these stunning machined billet aluminum frames work with our L58 kits to allow you to surface mount the lens on the outside of the sheet metal while the LED's and housing attach to the inside. The large L58 Frame is 16-3/4" long X just under 1" wide. It will protrude .400" off the surface. They accept our lenses perfectly (as shown). All other parts (lens, LED's, housing, etc) are in the flush mount kits, just add these frames for flat surface mount installation. 3rd Brake Light kits need one frame, Taillight Kits need two frames.
|
| #L58-FR (Large, each) |
$60.00 |
Small Hot Slots! For tighter spaces
Same as full size Hot Slots except... ●30 Super
Bright Red LED strips per light. ●Lenses are only 1/2" wide by 7-1/2"
long! Small Hot Slot Taillights.
Each light is split 20/10 to work with either integral turn signal/brakes or separate turn signal systems. |
|
Small Double-D LED Taillights
Two strips of 30 Super Bright Red LED's per light, inside an aluminum housing. 1/4" thick build-in, flush mounted red acrylic lenses with prismatic diffusers. Each strip is split 20-10 and the strips are wired separately so that you may wire the strips together or not. Work with integral turn/brake systems or vehicles with separate turn signals. The lenses are 1/2" wide x 7-1/2" long. Mounting hardware and dual intensity convertors included. |
|
| #L58SM-DDR -
Small Double-D LED Taillights (Pair) |
$190.00 |
| Or with clear lenses/diffusers.#L58SM-DDCL (Pair) |
$190.00 |
Small Sequential LED Taillights !
Our #L58SM taillights above, but three steps better. Each
light is split into three groups of 10 LED's that sequence
inside-out with the turn signals. Brake lights quickly sequences
once then all stay on.
All the necessary convertors, an electronic flasher and sequencing modules are included, with great instructions.
|
|
| #L58SM-SEQ (Pair) |
$275.00 |
Billet Frames for StreetWorks L58SM Series LED Lights
If you aren't into flush mounting taillight or 3rd brake light lenses into the body, these stunning machined billet aluminum frames work with our L58SM kits to allow you to surface mount the lens on the outside of the sheet metal while the LED's and housing attach to the inside. The small L58SM Frame is 9" long X just under 1" wide. It will protrude .400" off the surface. They accept our lenses perfectly (as shown). All other parts (lens, LED's, housing, etc) are in the flush mount kits, just add these frames for flat surface mount installation. 3rd Brake Light kits need one frame, Taillight Kits need two frames.
|
|
| #L58SM-FR (Small, each) |
$50.00 |
Sequencing Taillight Kit
Make your own Sequencing Taillights with our new kit. Provides modules, connectors and instructions to turn your three-lights-per-side taillights (bulb or LED) into sequencing taillights. If your have only (2) light segments that you want to have flash alternately, see part #L90 on the Other LIghts page for a less expensive kit. |
| #L58-TSK (For both
sides) |
$99.00 |
Deep Mount Small Hot Slots ! Flush Mounts
For Curved Surfaces
Now for the first time,
install flush mounted lights into curved surfaces! Our deep acrylic
lenses and steel support boxes allow you to contour the flush mount
surface as much as 3 inches. Fit into
curved fenders or under curved rear windows. 30 Super Bright Red LED
strips per light. Lenses are only
1/2" wide by 7-1/2" long! (Surface dimension will vary due to
curvature.) These are a weld-in or
glass-in kit requiring very good body working skills.
Each light is split 20/10 to work with either integral turn signal/brakes or separate turn signal systems.
|
 |
Small Deep Mount Sequential LED Taillights !
Our #L58SM-DP taillights above, but three steps better. Each light is
split into three groups of 10 LED's that sequence inside-out with the
turn signals. Brake lights quickly sequences once then all stay on.
All the necessary convertors, an electronic flasher and sequencing modules are included, with great instructions.
|
 |
| #L58SM-DP-SEQ (Pair) |
$350.00 |
NOTE: LED's used for
turn signals do not pull enough amperage to work a standard metallic
"can" flasher. You will need to use either a low amperage electronic flasher
as a replacement for the standard flasher or dummy loads which increase the
amperage draw through the flasher so the standard unit will still work.
LED Stop/Tail/Turn Light - SAE/DOT Compliant
A true surface mount LED taillight or 3rd brake light. The unit measures 1-3/16 wide” x 15-3/8” long and stands 11/16” tall off the surface. 10 Super Bright LED’s are wired for all three functions to use as a taillight (2 required) or it can be used as a 3rd brake light only. This light meets all SAE/DOT requirements. Black stainless steel mounting screws included.
|
| #L87 - LED Stop/Tail/Turn Light (Each) |
$50.00 |
LED Stop/Tail/Turn Light w/Billet End Cap Mounts - SAE/DOT compliant!
We’ve made this light easy to mount and great looking, too. Billet End Caps provide hidden surface mounting. The unit measures 1-3/8” wide x 15-9/16” long and stands 3/4” tall off the surface. 10 super bright LED’s are wired for all three functions to use as a taillight (2 required) or as a 3rd brake light only. This light meets SAE/DOT requirements and is so marked.
|
| #L87-BEC LED Light with Billet End Caps (each) |
$95.00 |
LED Dummy Load When using LED's for turn
signals your regular flasher doesn't work right anymore because the
LED's don't pull enough amperage to trigger it. This "dummy load" wires
in parallel with the LED to add the necessary amperage draw. One dummy
load per side is usually sufficient. |
 |
| #L52DL2 (Sold only in Pairs) |
$9.00/Pair |
Electronic Flasher for LED's
A direct plug-in to your 2-prong flasher panel socket. This solid-state (electronic) flasher works for loads from as-little-as 20 ma up to a heavy duty 25 amps maximum load. 1-1/8" square X 1-9/16" tall. |
 |
| #AM-02R Electronic Flasher for LED’s |
$25.00 |
Brake Light Pulsator
Get their attention fast when your brake lights pulsate at 300 pulses
per minute (5 per second!). Simple two wire connection - cut the feed
wire to the light(s) and install the STOP-ALERTTM with the terminals provided. Works for third brake lights or main brake
lights or both. Solid state, uses no additional power. Rated at 60 watts
continuous (5 amps incandescent), great for two #1157 bulbs or Ultra
Brights plus a 3rd brake light (for Halogen taillights, one per light is
needed).
Only 1-3/4" x 7/8" x 1-1/8. |
 |
3rd Brake Light Flasher
Makes your 3rd brake light flash 5 seconds when applied then come on solid. Get their attention without blinding them. It starts the flash over again when you reapply the brakes. Three wire connection, with terminals. Works with LED's or bulbs. Solid state, uses no power. Rated at 60 watts (5 amps incandescent), great for two #1157 bulbs or Ultra Brights plus a 3rd brake light (not for Halogen taillights). Small 1-3/4" x 7/8" x 1-1/8". |
|
Do-It-Yourself LED StripsRed LED's for Do-It-Yourself projects. All strips are 5/16" wide X 1/2" high (overall) X the length listed below.
As Do-it-Yourself items, these are sold without warranty.
|
|
| #L73-5 (5-LED strip, 1-1/4" long) |
$10.00 |
| #L73-10 (10-LED strip, 2-9/16" long) |
$15.00 |
| #L73-15 (15-LED strip, 3-7/8" long) |
$20.00 |
| #L73-20 (20-LED strip, 5-3/16" long) |
$25.00 |
| #L73-30 (30-LED strip, 7-3/4" long) |
$30.00 |
| #L73-60 (60-LED strip, 15-3/8" long) |
$50.00 |
Other sizes are available (in 5-LED increments)- please call!
Amber LED's for Do-It-Yourself projects. All strips are 3/8" wide X 1/2" high (overall) X the length listed below. As Do-it-yourself items, these are sold without warranty.
| #L73A-4 (Amb 4-LED strip, 1-3/8" lg) |
$10.00 |
| #L73A-8 (Amb 8-LED strip, 2-3/4" lg) |
$15.00 |
| #L73A-12 (Amb 12-LED strip, 4-3/16" lg) |
$20.00 |
| #L73A-16 (Amb 16-LED strip, 5-9/16" lg) |
$25.00 |
| #L73A-20 (Amb 20-LED strip, 6-15/16" lg) |
$30.00 |
| #L73A-24 (Amb 24-LED strip, 8-5/16" lg) |
$35.00 |
| #L73A-28 (Amb 28-LED strip, 9-11/16" lg) |
$40.00 |
| #L73A-32 (Amb 32-LED strip, 11-1/8" lg) |
$45.00 |
NOTE: These are single intensity lights. Should you want them to work like a dual intensity light, for example as an auxiliary running light (less bright) and turn signal (full bright), you will also need to purchase our conversion kit.
| #L-JE03 (for L73A-4/8 or L73-5/10/15/20, one per light) |
$5.00 |
| #L-JE02 (for L73A-12/16/20/24/28/32 or L73-30/60, one per light) |
$5.00 |
Lens Material
●Red lenses
material for your project. ●Red
translucent acrylic with or without diffuser 3" x 12" pieces only.
● 1/4" thick lens. |
|
|
#P-RLM (Red translucent acrylic, each) |
$15.00 |
|
#P-RLD (Red translucent acrylic with diffuser, each) |
$25.00 |
Rod Bits:
The street rod and custom car industry has been responsible for many firsts in parts and styling that later transferred to "main-stream" cars. While LED Taillights in street rods were not a first, our industry has definitely contributed more, and faster, than anywhere else. Watson's StreetWorks remains at the front of that contribution providing an extensive selection of LED Flush mounted Taillights, Do-it-Yourself LED strips, and all of the parts that you need to make them work on your car - not the least of which is knowledge. We know LED's and how they work. So when you buy from us, you not only get the product you want, you also get a team of experts to help you along the way. You want your ride to be a standout, something very special, and so do we.
|
